Part no.: 09 0063 00 07
Bayonet Male cable connector, Contacts: 7, 5.0-8.0 mm, shieldable, solder, IP40
Bayonet, series 690, Power Connectors
This male cable connector with bayonet locking system and a pin count of 7 is according to its protection class IP40 protected against solid foreign bodies and against access with a wire. No protection against water. It can be used in areas with a pollution degree of 1. In places where there is no or only slight, but non-conductive soiling. The pollution has no influence. With temperatures ranges of -40 °C/85 °C is this shieldable bayonet male cable connector designed for both severe cold and severe heat. Due to the qualified rated voltage of 250 V and the rated current of 5,0 A it is perfectly tuned for its field of application.
General features
MorelessPart no. | 09 0063 00 07 |
Connector design | Male cable connector |
Version | Connector pin straight |
Connector locking system | Bayonet |
Termination | solder |
Degree of protection | IP40 |
Cross-sectional area | 0.75 mm² / AWG 18 |
Cable outlet | 5.0-8.0 mm |
Temperature range from/to | -40 °C / 85 °C |
Mechanical operation | > 50 Mating cycles |
Weight (g) | 37.85 |
Customs tariff number | 85369010 |
Country of Origin | DE |
Electrical parameters
MorelessRated voltage | 250 V |
Rated impulse voltage | 2500 V |
Rated current | 5.0 A |
Insulation resistance | ≥ 1010 Ω |
Pollution degree | 1 |
Overvoltage category | II |
Insulating material group | III |
EMC compliance | shieldable |
Shield connection | Cable clamp and soldering lug |
Material
MorelessHousing material | GD-AL eloxiert |
Contact body material | PET (UL94 V-0) |
Contact material | CuZn (brass) |
Contact plating | CuSnZn (Optalloy) |
REACH SVHC |
CAS 7439-92-1 (Lead) |
SCIP number | ad2cdc83-d3f8-4fd6-ab3a-dd5db6db68ad |
Classifications
MorelesseCl@ss 11.1 | 27-44-01-09 |
ETIM 9.0 | EC003569 |
Declarations of conformity
MorelessLow Voltage Directive | 2014/35/EU (EN 60204-1:2018;EN 60529:1991) |
General Disclaim Notice
- The connector must not be plugged or unplugged under load. Non-observance and improper use can result in personal injury.
- The connectors have been developed for applications in plant engineering, control and electrical equipment construction. The user is responsible for checking whether the connectors can also be used in other areas of application.
- To protect against unintentional opening of the connector, the thread between the housing and the connector head must be secured with a suitable cyanoacrylate adhesive when used in circuits with voltages dangerous to the touch. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
- Connectors which are used in circuits with voltages dangerous to the touch may only be installed and used by, or under the supervision of, persons with electrical engineering training, taking into account the applicable regulations and standards.
- The user must take suitable safety precautions to ensure that the connector cannot be accidentally disconnected.
- The plug connector is not suitable for mains voltages Please observe the pollution degree and the overvoltage category. For further information, please refer to the download center "Technical Information".
- To lock the cable connector to the device connector, we recommend tightening the threaded ring to 1.25 Nm. A suitable torque wrench is available as an accessory (order no. 07 0082 000).
Downloads