Menu
Back
  1. Products
  2. Automation technology - Sensors and actuators
  3. M12-A
  4. M12 Male cable connector, Contacts: 8, shielded, moulded on the cable, IP67, Ethernet CAT5e, TPE, black, 4 x 2 x AWG 24, 3 m
Part no.: 77 3529 0000 64708-0300

M12 Male cable connector, Contacts: 8, shielded, moulded on the cable, IP67, Ethernet CAT5e, TPE, black, 4 x 2 x AWG 24, 3 m

M12-A, series 763, Automation Technology - Sensors and Actuators
(Other lengths are available on request).
Compare product
Downloads
This male cable connector with screw locking and a pin count of 8 is according to its protection class IP67 Dust-tight and has complete protection against contact and protection against temporary immersion. It can be used in areas with a pollution degree of 3. In places where contamination can occur that is conductive or can become conductive through condensation. With temperatures ranges of -25 °C/90 °C is this shielded M12-A coded male cable connector designed for both severe cold and severe heat. Due to the qualified rated voltage of 30 V and the rated current of 2,0 A it is perfectly tuned for its field of application. It complies with the type standard DIN EN 61076-2-101.
General features
Moreless
Part no. 77 3529 0000 64708-0300
Connector design Male cable connector
Type standard DIN EN 61076-2-101
Cable length 3 m (Other lengths are available on request).
Version Connector pin straight
Connector locking system screw
Termination moulded on the cable
Degree of protection IP67
Cross-sectional area 0.25 mm² / AWG 24
Temperature range from/to -25 °C / 90 °C
Mechanical operation > 100 Mating cycles
Weight (g) 192
Rated voltage 30 V
Rated impulse voltage 800 V
Rated current 2.0 A
Pollution degree 3
Overvoltage category II
Insulating material group II
EMC compliance shielded
Contact body material PUR
Contact material CuZn (brass)
Contact plating Au (gold)
SCIP number SCIP-number not available
ETIM 9.0 EC002638
Cable data
Moreless
Structure of the cable
Cable type Ethernet CAT5e
Cable diameter 7.6 mm
Cross section 4 x 2 x AWG 24
Sheath material TPE
Single-lead insulation HDPE
Single-lead structure 7 x 32 mm
Cable color black
Mechanical properties
Bending radius, fixed cable ≥ 5 x Ø
Bending radius, moving cable ≥ 10 x Ø
Bending cycles > 10 million
Permitted acceleration max. 2 m/s²
Travel speed ≤ 200 m/min (5 m horizontal distance)
Thermal properties
Temperature range cable in move from/to -40 °C / 80 °C
Temperature range cable fixed from/to -40 °C / 80 °C
General Disclaim Notice
  1. The connector must not be plugged or unplugged under load. Non-observance and improper use can result in personal injury.
  2. The connectors have been developed for applications in plant engineering, control and electrical equipment construction. The user is responsible for checking whether the connectors can also be used in other areas of application.
  3. To protect against unintentional opening of the connector, the thread between the housing and the connector head must be secured with a suitable cyanoacrylate adhesive when used in circuits with voltages dangerous to the touch. This does not apply to connectors used in SELV and PELV circuits according to IEC 61140 (EN 61140, VDE 0140-1).
  4. Connectors which are used in circuits with voltages dangerous to the touch may only be installed and used by, or under the supervision of, persons with electrical engineering training, taking into account the applicable regulations and standards.
  5. The user must take suitable safety precautions to ensure that the connector cannot be accidentally disconnected.
  6. Plug connectors with enclosure protection IP67 and IP68 are not suitable for use under water. When used outdoors, the plug connectors must be protected separately against corrosion. For further information on the IP protection classes, please refer to the "Technical Information" download centre.
  7. The plug connector is not suitable for mains voltages Please observe the pollution degree and the overvoltage category. For further information, please refer to the download center "Technical Information".
  8. To lock the cable connector with the device connector, the threaded ring is tightened "hand-tight" (approx. 60 cNm).
  9. The protection class specification applies on condition that the four mounting holes are made as blind holes.
Downloads
Data sheet
Data sheet 77 3529 0000 64708-0300
PDF
REACH
77 3529 0000 64708-0300
PDF
RoHS
77 3529 0000 64708-0300
PDF
China RoHS
77 3529 0000 64708-0300
PDF
CAD files
Select required format
M12-A
77 3529 0000 64708-0300